How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (2022)

Whirlpool washers and dryers with hi-end functions and innovative features strive to make the mundane chore of washing clothes easy. However, these Whirlpool washers are not foolproof and could develop problems of their own, such as issues with their sensing light. So, how do you fix the sensing light flashing problem in your Whirlpool washing machine?

To fix your whirlpool washer sensing light flashing, reset the appliance. Access the technical datasheet from the console to get the error code. Refer to your instruction manual to troubleshoot/resolve the error. Replace parts if faulty, but first, check for blockages in drain hose/pump or impeller.

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (1)

Continue reading to know more about how you can troubleshoot your Whirlpool washing machine, spot the exact problem, and resolve it.

What Does a Blinking Sensing Light Indicate?

The sensing light on your Whirlpool washer lights up when you start the appliance, with the “water level” knob set to “auto-sensing.” Your washer senses the contents to assess the load size and balance to decide on the right amount of water to clean the load. Once the sensing is done, the washer gets filled to the auto-set water level, and the wash phase begins.

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (2)

Blinking sensing light at the start of a new wash cycle indicates that the machine is doing its job. However, if the cycle doesn’t move on from the sensing phase, you may be experiencing a problem with the load size, or the sensor itself.

The following are things you could do to address the sensing light flashing problem.

Reset Your Whirlpool Washer

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (3)

Whirlpool has an online repository of product manuals and product help literature that may come in handy to troubleshoot common washer problems. Look for model-specific instructions as even the most basic tasks, such as resetting a washer will be different for each model.

(Video) Washing Machine Stuck on Sensing or Not Washing Don't Throw It Away Try This Cheap Fix!

Update: we added an article that will help you reset various models and features of a whirlpool washer.

One way to reset your Whirlpool washing machine is to switch off the appliance, unplug the unit, and leave it untouched for about 15 to 20 minutes before powering it on again.

You may unplug and plug in the washer and turn the power on. Lift and close the lid about six times within 12 seconds to reset the unit.

You can also reset your washer by checking your product manual. Start a new wash cycle and test the appliance.

Get Into Diagnostics to Find the Exact Error Code

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (4)

There could be different reasons your washer could be acting strangely. Getting to know the exact problem will save you a lot of effort otherwise spent on its diagnosis. Whirlpool washers, like other brand washing machines, display an error code that defines the fault.

Here is how you can find the error code for your washer issue:

  1. Use the mode dial to get into diagnostics.
  2. Set it to Normal.
  3. Turn it one click to the left, three clicks to the right, one click left, and then one click right.
  4. Get the error code from the technical data sheet on the console.

Use the error code to record a service request or handle the repairs yourself. The code will determine how the problem needs to be addressed. If the fix calls for replacing faulty parts, procure the component compatible with your particular model.

Try the Drain and Spin Functions

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (5)
(Video) Fixing A Kenmore/Whirlpool HE Washing Machine Stuck In Sensing Mode!

In some cases, even getting into the diagnostics could be tricky.

In case your washer has stopped midway with the sensing light flashing, and you are unable to access diagnostics, check if you can drain the water and use the spin function.

If the water drains from the unit, but your Whirlpool Washer won’t spin, you may have a problem with the shift actuator. Replacing the actuator may help you get into diagnostics and proceed with troubleshooting and resolution.

If your Whirlpool Washer won’t drain, you cannot use the spin function or Whirlpool won’t start a new wash cycle. If that’s the case, move to the next step.

Look for Blockages in the Drain Hose, Pump, Impeller

It is common for lint to build up in your washer. Other small objects like pins and buttons too are likely to collect inside the unit. While regular maintenance can prevent clogging of the drain hose and other internal parts, you may still have a block in the draining system.

Copyright protected content owner: Readytodiy.com and was 1st posted on 2020-07-30. .

Check for blockages and clear them for water to drain from your washer.

Removing the drain hose may not be much of a challenge. But it’s recommended you seek professional help or advice when working with the pump and impeller. This is because you’ll have to disassemble the units, clean them, and put them back in place to ensure the washer works fine.

Replace Faulty Parts Based on Error Code

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (6)
(Video) how to reset washing machine (Whirlpool) - Rest your washer with this quick recalibration cycle

If you are a DIY enthusiast who is comfortable fixing home appliances on your own, you may be eager to replace washer parts to check if it resolves the issue. However, there are a couple of things you need to keep in mind:

  • Go ahead with replacements only if the error code indicates the need for a new part.
  • Shop for parts that are intended for your washer model. You will find the model number beneath the lid of the machine. Sample parts code looks like this: W10467289 Temperature Sensor, W10178988 Sensor or search brand and model.

Possible Reasons for Faulty Drain/Spin Functions

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (7)

A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. In most cases, these problems can be easily fixed if you know what to do.

While the error code proves helpful at locating the problematic component, you may find it useful to know the possible reasons for the faulty spin/drain functions as they could prove valuable when troubleshooting the issue.

Copyright article owner is Readytodiy.com for this article. This post was first published on 2020-07-30..

Water will not drain from your Whirlpool washer if:

  • There are obstructions in the drain pump or hose.
  • The drain hose is twisted, bent or coiled.
  • The coin trap, which traps small objects that get into the drain, is clogged with debris.
  • The lid switch assembly/ door lock switch assembly on the unit is defective and your Whirlpool washer door won’t lock. The washer will function only when the lid/door is completely closed and locked.
  • The water pump belt in the washer has worn out or is damaged.

Kindly note, some of these components will be present only in select washer models.

When you are battling with a faulty spin function, check if:

  • The door lock switch assembly/lid switch assembly is working fine. If this component is faulty, your washer will not work until the fault is fixed.
  • The door latch seals the unit completely when shut.
  • The motor coupling is intact and in working condition.
  • The motor control board receives and transmits power to the washer’s motor.
  • The drive belt is loose or damaged.

Faulty components must be repaired or replaced to get the washing machine up and running again. Some of these parts are prone to mechanical as well as electrical faults. Use a multimeter to check all the switches on door/lid assemblies for electrical continuity. Replace switches that do not have continuity and check if the fixed units work fine.

(Video) Whirlpool washer reset calibration

If you are not familiar or comfortable with troubleshooting or fixing washing machine problems on your own, get a technician on board. Having said that, some of these problems/solutions do not require professional intervention.

Final Thoughts

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (8)

Whirlpool washing machines serve innumerable households the world over. But like every consumer good, they too are prone to wear and tear, and faults. There’s a lot of information available online that can help resolve several of these common problems on your own.

Therefore, the next time you run into a problem with your washer, try to address the issue by yourself or at least attempt a few simple solutions before seeking expert help. You’ll save money and also learn a thing or two in the process.

Related Article

My Whirlpool Washer Isn’t Working (Repeating Cycle, Keeps Draining/Shutting Off)

Whirlpool Washer Leaking

Whirlpool Washer Odor or Smell Problem

ReadyToDiy is the owner of this article. This post was published on 2020-07-30..

Whirlpool Washer Won’t Rinse or Won’t Wash

(Video) Whirlpool Washer Blinking Locked Light

How to Fix Whirlpool Washer Sensing Light Flashing - Ready To DIY (9)

FAQs

How do I reset the sensor on my Whirlpool washing machine? ›

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.

Why does my Whirlpool washer keep saying sensing? ›

If the water level seems too low, or if the washer does not fill completely, auto-sensing helps stabilize the amount of water used. The washer senses the size of the load and adds the correct amount of water for the load size. You may notice during a cycle that the wash load is not completely submerged in water.

Why is my Whirlpool washer light blinking? ›

The Wash Light is On or Flashing when the water level does not change for a period of time OR water is present but the control does not detect the water level changing.

How do you reset a washing machine sensor? ›

The power supply yikes brand is really in there unplug the power supply for about a minute. After

How do I fix my Whirlpool sensing? ›

First, try to cut off power to the machine for a few minutes (about 3-5 minutes) then reconnect it to power and see if it will behave. Quick Tip: Every so often, leaving the washer unplugged for longer (you can even leave it unplugged for 15-20 minutes) does the magic.

Why is my washer stuck on sensing? ›

When it gets stuck on sensing, it's likely because of a faulty water inlet valve, shift actuator, drive motor, or main control board. A fault at any of those parts can prevent the washer from advancing past the sensing stage.

Where is the sensor on Whirlpool washer? ›

Whirlpool Washer Repair - How to Replace the Temperature Sensor

How do you put a Whirlpool washer in diagnostic mode? ›

Whirlpool Washer Test/Diagnostic Mode - YouTube

What does sensing fill mean? ›

SENSING/FILL Light is on

When the Start/Stop button is pressed, and the Water Level knob is set to Auto Sensing, the washer will fill and begin sensing to determine load size and balance.

How do I bypass the lid switch on a Whirlpool washer? ›

See how to bypass the lid switch in a Whirlpool washer - YouTube

How long is sensing fill? ›

These sensing spins may take 2 to 3 minutes before water is added to the load. The washer will then move the load briefly, pause to allow water to soak into the load, and resume adding water. This process may repeat until the correct amount of water has been added to the load.

Does unplugging a washer reset it? ›

Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.

How do you calibrate a Whirlpool washing machine? ›

Whirlpool washer reset calibration - YouTube

Where is the sensor located on Whirlpool washer? ›

Whirlpool Washer Repair - How to Replace the Temperature Sensor

Where is the load sensor switch on a Whirlpool washer? ›

This sensor switch is located in the top console of the washer, and is usually labeled as the water temperature control (A.T.C. control). This switch senses the load inside the washer, and automatically adjusts the water level in the tub to the proper level.

How do you test a washing machine water level sensor? ›

How to Test the Pressure Switch on your Washer - YouTube

How do I calibrate my Whirlpool washing machine? ›

Whirlpool washer reset calibration - YouTube

Videos

1. Automatic load sensing on your washing machine
(W Service)
2. Whirlpool washer Reset
(WaterMitigationAdvice)
3. IS YOUR WASHER'S LID LOCK LIGHT BLINKING?* FIX IT * EASY & FREE* *2020*
(Educational Entertainment Videos)
4. How to Read a Vertical Modular Washer (VMW) Error Code Display
(Sears PartsDirect)
5. How to Do a Whirlpool Washer Reset & Recalibration
(Bens Appliances and Junk)
6. How to Replace Newer Whirlpool Top Load Washer Lid Lock and Fix Lid Striker Issue (W11307244)
(Bens Appliances and Junk)

Top Articles

You might also like

Latest Posts

Article information

Author: Jeremiah Abshire

Last Updated: 12/06/2022

Views: 6713

Rating: 4.3 / 5 (54 voted)

Reviews: 85% of readers found this page helpful

Author information

Name: Jeremiah Abshire

Birthday: 1993-09-14

Address: Apt. 425 92748 Jannie Centers, Port Nikitaville, VT 82110

Phone: +8096210939894

Job: Lead Healthcare Manager

Hobby: Watching movies, Watching movies, Knapping, LARPing, Coffee roasting, Lacemaking, Gaming

Introduction: My name is Jeremiah Abshire, I am a outstanding, kind, clever, hilarious, curious, hilarious, outstanding person who loves writing and wants to share my knowledge and understanding with you.