Why GE Dishwasher Won’t Start Just Beeps? – DIY Appliance Repairs, Home Repair Tips and Tricks (2023)

DISCLOSURE: This post may contain affiliate links, meaning when you click the links and make a purchase, we receive a commission at no additional cost to you

Your GE dishwasher has a voice, sort of. It beeps whenever it’s unhappy about something or appears to have something wrong with it. This can be frustrating when it beeps with no error code showing up on the display because you have no idea what’s wrong with it. It can be particularly aggravating if you press start but it won’t start. It just beeps.

There are some possible explanations for why GE dishwasher won’t start just beeps. It may be reacting to a power surge or the door latch isn’t functioning correctly. It could also be something awry with the heater.

We’ll walk you through the basics of this problem in the article below. You are probably able to fix this issue without calling a service repair technician. You will find that the type of beep you hear is a signal to the problem.

Constant Beeping Sound

A dishwasher that has both beeping sounds and blinking lights usually indicates it was subjected to a power surge. This can be easily fixed by resetting the dishwasher. To do that, press the button for start or reset. The dishwasher should be back to normal and start running as before in about three minutes.

The issue can return. If it does, do a hard set on the dishwasher. A hard reset is when you cut it from power for 10 minutes. The power cord may not be accessible. In that case, flip the circuit breaker dedicated to the dishwasher off.

Why GE Dishwasher Won’t Start Just Beeps? – DIY Appliance Repairs, Home Repair Tips and Tricks (1)

The dishwasher should resume its cycle once you turn the power back on.

Read: 5 Reasons Why GE Dishwasher Not Draining

(Video) ✨ GE DISHWASHER-THREE BEEPS - Won’t Start ( Easy FIX )✨

Timed Beeping Sound

Your dishwasher may make a beeping sound 30 seconds to a minute apart when you start it. This tells you the door is unlatched. Stop the dishwasher, open the door and close it firmly. Press start again and see if the beeping stops.

Why GE Dishwasher Won’t Start Just Beeps? – DIY Appliance Repairs, Home Repair Tips and Tricks (2)

Running an Operation Check

You can run a door status check to see if the latch is the issue. Hold down the “select cycle” and “start” buttons at the same time for five seconds. The dishwasher will go through a door status check for 10 seconds after that. A closed-door will show solid LED lights. An open door, or a problem with the latch, will show up as flashing LED lights.

The LED lights will cut off after the door status check, except for the lock LED. This is when you want to run an operations check that runs through the workings of the drain pump, the water valve, the circulation pump, the heater, and the detergent solenoid.

You will start this test while the lock LED is lit. Hold down the “select cycle” for five seconds. Then, press it again to the selects/increments test. Press “start” to start the test. You can also press

“start” to stop it if you need to do so.

Connect with an Appliance Repair Tech

Click here to use the chatbox to speak with one of our technicians.
No in-home service calls. No appointments.

This test will use LED lights to indicate the tests being run. The lights are as follows:

(Video) ✨ GE DISHWASHER-3 BEEPS-WON’T START (FIXED) ✨

  • One blink means the drain pump is running.
  • Two blinks indicate the water valve is filling the tub.
  • Three blinks mean the circulation pump is changing the diverter.
  • Four blinks indicated the heater is on.
  • Five blinks show the detergent solenoid is on maximum use.

The entire test should only take six minutes at most.

Why GE Dishwasher Won’t Start Just Beeps? – DIY Appliance Repairs, Home Repair Tips and Tricks (3)

Read: Should You Use Dishwasher Detergent Substitute’s?

A Perplexing Problem

People routinely show up on appliance forums asking about a dishwasher that won’t start. One GE dishwasher owner said all her buttons worked and the appliance had power. She said it beeped three times when she pressed start but nothing happens.

She did a hard reset on the appliance, ran the error mode, ran the service mode and everything came up clean. The dishwasher showed no irregularities or errors. The start button worked well during the different modes.

Yet, it beeped again and wouldn’t start when she returned to start the dishwasher after the diagnostic modes.

She then did a door status check. Nothing was wrong there. She ran another test on operations and the dishwasher passed.

The appliance technician then gave her a piece of simple advice. He said to press and hold the “heated dry” and “start” buttons simultaneously for five seconds. Then, try to run a cycle. It worked.

Read: Why Is Dishwasher’s Detergent Door Not Opening?

(Video) How to fix the GE beeping dishwasher issue

What do you do when your dishwasher isn’t starting?

Do the obvious first. See that the dishwasher has power. You can check the outlet or look to see if the circuit breaker is flipped. Check your wall switch or a switch under the sink to see if the power is on.

If none of those things work, you will need to reset the machine to see if that makes a difference. Then, you should run a diagnostic test if the dishwasher turns on.

Why is the start button flashing on my GE dishwasher?

It means the cycle was interrupted. The light will blink if you press the “start” button after a cycle starts. This tells you the appliance is draining water and going into “standby” status.

This situation can also happen if you don’t interrupt the cycle by pressing a button. A blinking “start” light could mean that the door was opened during a cycle or power was disrupted.

Read: Why Dishwasher Hums And Not Getting Water?

Could the thermal fuse be the problem?

A faulty thermal fuse could cause your dishwasher to not start but wouldn’t be associated with the beeping sound. A failed thermal fuse will not send power to the control board so your dishwasher won’t start.

Where is the thermal fuse on a GE dishwasher?

Typically, the thermal fuse is on top of the circuit board assembly. It has two wires connected to it.

Do GE dishwashers have a lot of problems?

GE dishwashers don’t have a lot of problems and their problems aren’t any more frequent or severe than other brands. GE is a reliable company.

The most common problems GE dishwashers have are water filling issues, water leaks, draining problems, and the appliance suddenly stopping during a wash cycle.

There are also “cleaning issues” which means the drain can get clogged. However, you are supposed to clean your dishwasher twice a year to prevent that.

How long will a GE dishwasher last?

The average lifespan of any dishwasher is between nine to 10 years. Some can last longer depending on how well you maintain them.

When will a dishwasher start needing repairs?

Consumer Reports states most dishwashers need some type of repair within five years. However, most dishwasher repairs are smaller problems at that point so they shouldn’t be expensive or involved.

Read: Why Is My Dishwasher Making Loud Noises?

Do plumbers work on dishwashers?

Plumbers don’t repair dishwashers but they often install them. Dishwasher installation involves hooking up water and power so plumbers are well suited for that and will do a good job.You should call an appliance repair technician if your dishwasher needs repair.

Why is my dishwasher beeping randomly?

Dishwashers do beep at certain points during the cycle to let you know one cycle is done and another started. However, beeps can also indicate a part is failing.

You will know this type of beep if it happens at unusual times or seems to be happening more often.

(Video) My GE Dishwasher just beeps three times and wont' start. The

Resetting a GE Dishwasher to Clear Codes

It’s an easy task to reset the control panel to clear all codes in a GE dishwasher. Press the “start” button for five seconds. It will flash. Now, press both the “start” and the “select cycle” button down at the same time for five seconds.

The control panel should be cleared. It should light up with everything operating normally.

FAQs

Why does my GE dishwasher beep and not start? ›

Beeping Sound, Blinking or Will Not Start: A beeping sound every 30 seconds or every minute: This indicates the dishwasher door was unlatched during the cycle. Close the dishwasher door to resume the cycle and the beeping will stop.

How do you reset a GE dishwasher that won't start? ›

Hold the Start button now for five seconds. The Start button should start flashing. Finally, hold the Start and Select Cycle button down for five seconds. The dishwasher control panel should now light up, and the dishwasher should be ready to go.

What do you do when your GE dishwasher won't start? ›

Common Causes for a GE Dishwasher Not Starting
  1. Make sure the dishwasher is correctly plugged into a functioning electrical outlet.
  2. Confirm that the power switch is on. ...
  3. Check your home's circuit breaker or fuse box for tripped breakers or blown fuses.
1 Aug 2020

How do I reset my GE dishwasher control board? ›

To reset a GE dishwasher, press the Start or Reset button during a cycle. If you have a top-loading dishwasher, you'll need to open the top, press the button, and close it again.

How do I reset my dishwasher sensor? ›

Dishwashers usually don't have a dedicated reset button on the control panel. You can reset your dishwasher by unplugging it from its power source for one minute and then plugging it back in.

Why is my dishwasher flashing and beeping? ›

If the dishwasher is beeping alongside blinking lights, the anti-flood device may have been activated. This means that the sensors have detected water in the casing and have stopped working to prevent flooding. You'll need to tilt the appliance to get rid of excess water, and sponge off water in the base.

What are the five reasons a dishwasher won't start? ›

Table of Contents
  • Check the Power Supply.
  • Inspect the Door Latch.
  • Check the Child Safety Lock.
  • Reset the Dishwasher.
  • Turn Off the Power Before Disassembling the Dishwasher.
  • Test the Door Latch Switch.
  • Test the Timer.
  • Test the Selector Switch.
26 Sept 2022

What causes a dishwasher not to start? ›

If your dishwasher won't start, the problem could be the door latch or door latch switches. The door latch assembly is used to hold the door closed during the cycle to prevent water from leaking and it also incorporates the door latch switches that supply power to the dishwasher controls.

Do GE washers have a reset button? ›

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

What causes dishwasher control panel to stop working? ›

There are several reasons why your dishwasher buttons may not be working. There could be dirt build-up, there could be an electrical problem, or there could be an issue related to the trap and filter. You should start by cleaning the dishwasher buttons thoroughly.

What is the most common problem with a dishwasher? ›

1. Dishes Are Not Coming Out Clean. One of the most common complaints with any dishwasher is that it does not clean dishes effectively. If your dishwasher suddenly seems to be ineffective, you may need to complete some repairs.

How do you fix a beeping dishwasher? ›

Unplug your dishwasher from the wall. Then, give it approximately five minutes before plugging it back in. Allow your dishwasher to start up again, and see if the beeping has gone away. If it has, then you have fixed the problem, and you should be able to restart the wash cycle.

Why is my DishDrawer beeping? ›

The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. once to stop the beeping, and then again to clear the fault.

Is it worth fixing a dishwasher? ›

If the repairs would cost 50 percent or more of the cost of a new unit, you should replace it. So, if it would cost $500 to replace your current dishwasher, you shouldn't pay more than $250 to fix it. Another sign it's time to get a new dishwasher is if you've made repairs multiple times in the last year.

How do I reset the lid lock on my GE washer? ›

Top Load Washer - Lid Lock Feature
  1. Make sure the washer is paused (press the Start/Pause button). During the spin cycle, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid.
  2. Unplug the washer for a minute to reset.

What are common problems with GE washers? ›

Water flow issues are among the more common problems in GE washing machines, and they are generally easy to fix. If your washer won't fill, check the hot and cold faucets to make sure they're both turned on fully. GE washers require water pressure between 10 and 120 pounds per square inch.

Why is my GE dishwasher beeping? ›

A dishwasher that has both beeping sounds and blinking lights usually indicates it was subjected to a power surge. This can be easily fixed by resetting the dishwasher. To do that, press the button for start or reset. The dishwasher should be back to normal and start running as before in about three minutes.

Is there a fuse on a GE dishwasher? ›

If you've ruled out the door latch and door switch as the cause of your GE dishwasher not starting, the next step is to check the thermal fuse. The point of the thermal fuse is to shut your dishwasher off when it overheats. Sometimes the fuse blows, and this will stop your dishwasher from starting.

Why won't my dishwasher won't start? ›

If the dishwasher won't do anything at all, the problem could be the power supply. Check the circuit breaker. If it has tripped, flip the switch to the “off” position and then turn it back on. If the circuit has not tripped, check to ensure that the appliance is properly plugged into its wall outlet.

How do I get my GE dishwasher to stop beeping? ›

To turn off the control panel sound or tones, you press the Heated Dry or Power Dry pad 5 times in a row quickly. This turns off all tones and beeping, including the signal at the end of the cycle.

What does it mean when your dishwasher beeps 3 times? ›

If the dishwasher beeps 3 times or the LED flashes 3 times it indicates a leak, and water collecting at the bottom of the appliance. To resolve the issue, contact an Authorized Service Center. Warning: Turn off the dishwasher water supply to avoid flooding.

Why is my dishwasher blinking and not starting? ›

If you notice Start/Resume light flashing, it indicates cycle or start-up interruption. Now, this usually happens if the door has been opened during a cycle (or if power is interrupted).

How do you reset a GE washer? ›

Motor Reset Procedure:
  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ...
  3. The motor has now been reset and is ready for you to start a cycle.

Why does my DishDrawer keep beeping? ›

A fault has occurred. Your DishDrawer™ will self‐diagnose and let you know there is a problem by beeping continuously and displaying a fault code.

Videos

1. GE dishwasher won't run. beeps 3 times wont wash. how to fix this problem
(Tony K Is Mr. FIX IT)
2. My dishwasher won't start. It has power, but just beeps 3
(JustAnswer-Q&A)
3. GE Dishwasher Service Mode Not Working (Broken Control Board)
(NolanHergert)
4. GE dishwasher will not start , dishwasher has power but wont start, dishwasher door latch repair
(Off Da Hook & Moore)
5. GE dishwasher fix for blinking light and won't start
(dmm5157)
6. GE Dishwasher Won't Start? Replace Door Latch #WD21X10490
(RepairClinic.com)
Top Articles
Latest Posts
Article information

Author: Arielle Torp

Last Updated: 02/04/2023

Views: 6458

Rating: 4 / 5 (61 voted)

Reviews: 92% of readers found this page helpful

Author information

Name: Arielle Torp

Birthday: 1997-09-20

Address: 87313 Erdman Vista, North Dustinborough, WA 37563

Phone: +97216742823598

Job: Central Technology Officer

Hobby: Taekwondo, Macrame, Foreign language learning, Kite flying, Cooking, Skiing, Computer programming

Introduction: My name is Arielle Torp, I am a comfortable, kind, zealous, lovely, jolly, colorful, adventurous person who loves writing and wants to share my knowledge and understanding with you.